(Note: I initially tried doing it without installing DOS using fdisk and format and manually adding the autoexec.bat and config. If not, go to the Add New Hardware Wizard in the Control Panel and see if that detects it. Make sure you check to make sure Windows 95 is seeing your CD drive. It might have been because I either did or didn't restart after putting in the Windows 95 CD. I actually just got it to load the drivers off the Windows 95 CD by just trying it over and over again until it worked. cab files (you would need to extract them 1 by 1 and put them on floppy images to use them). You can find all of these drivers on the windows 95b CD if you have it, as they are all in. You might run into troubles when it tries to install the other drivers as it might ask you for Windows floppies even if you're using the CD version. Put your Windows 95 CD in the CD drive and type: d:\ usually 5)Ĭreate a blank floppy image either in VMware or MagicIso, then mount that new one. (this part /M:x refers to the amount of buffers your drive has. On the good side, every boot does not need to go step-by-step. So I think if DOSBox-X can emulate such a protocol, then you can just use existing. There are similar 3rd-party tools for other guest systems such as Win9x too. When arriving at the desktop, it locks up every time unless and until the SB16 device is removed. VMSMOUNT is such an example for DOS guest systems (it is included in FreeDOS), which allows access to VMwares shared folders as a normal drive letter without using tools from VMware. More than once it locks up at the W98SE splash screen. Now move to your C drive and type: mscdex.exe: /d:mscd001 /M:5 /V /L:d /S /K To make progress, change the command-line option to -boot c. Now add a line that says this c:\mscdex.exe /d:mscd001 type: edit config.sysĪdd a line that says this: device=c:\cdrom.sys /d:mscd001įind autoexec.bat in your C drive. run the following commands: a:\įind config.sys in your C drive. If you boot from the boot disk and dont mount the HDD images filesystems, you dont need /is (Scandisk worked fine for me). Go back to your virtual machine and mount the floppy image we just created. I used a Windows 98 boot disk image to start the setup process. (if you can't see the extensions you're going to need to change your folder options to show extensions) Find the file we just saved in Explorer and change the extension from.Drag both these files into MagicIso on the floppy disk we just created.(might have to try another if it doesn't work) Find a copy of mscdex.exe and oakcdrom.sys (generic CD-Rom driver that works with DOS.Put your DOS floppy/image in or mount it and install DOSĭownload and install the free version of MagicIso.Create a new virtual machine (make sure to add a floppy image drive if you are using VMware).a copy of MSCDEX.EXE and oakcdrom.sys (both can be found online).MagicIso (the free trial version will do).VMware player (it's free) or VirtualPC (I recommend VMware).That's exactly the situation I'm describing here.You should use VMware Player for Windows 95, as it has officially support for that. Not safe mode on host, of course, I'm talking about starting win98 in safe mode inside the VM (which works) Is there some setting I can tweak to get rid of this issue? the same VM runs fine on my AMD FX-8320E host, using VBOX 7.0.6.Įdit: the W98 VM boots correctly in safe mode, strangely enough, but not in normal mode. What could be causing this? windows 11 or the intel CPU (11th gen i5-11400H)? Tried VBOX 6.1.42 and 7.0.6 and both give me the same results. So ,I decided to start over and create a new VM, installed W98 from scratch and everything goes well until the very first logon, where I get that same error and I'm stuck. Every single time I have to login using 'safe mode.' Im banging my head over this. It seems that no matter which video driver I choose, it will not boot into 256 colors or greater. The VM boots, but just before the desktop appears i get errors relating to SHEL元2.dll being linked to SHLWAPI.DLL tFileAttribitesSA wich doesn't exist. Im having problems getting the video drivers to work in DosBox for Windows 98. I copied a W98 Guest machine I have on my PC to a newer laptop with an Intel i5 11th generation CPU and Windows 11.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |